09/07/16 18:09:17 31SWA630_150
Playing the AM/FM Radio (LX model)
U.S. and Canadian LX models
AM
FM
BUTTON BUTTON
POWER/
VOLUME KNOB
TUNE KNOB
A.SEL/SCAN
BAR
SEEK/SKIP BAR
PRESET BUTTONS
145
09/07/16 18:09:27 31SWA630_151
Playing the AM/FM Radio (LX model)
－ The scan function samples
SCAN
To Play the AM/FM Radio
To Select a Station
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
power/volume knob or the AM or
FM button. Adjust the volume by
turning the power/volume knob.
You can use any of five methods to
find radio stations on the selected
band: tune, seek, scan, the preset
buttons, and auto select.
all stations with strong signals on the
selected band. To activate it, press
the right side of the A. SEL/SCAN
bar, then release it. You will see
SCAN in the display. The system will
scan for a station with a strong signal.
TUNE － Use the TUNE knob to
tune the radio to a desired frequency. When it finds one, it will stop and
The band and frequency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is broad-
casting in stereo. Stereo
Turn the knob to the right to tune to
a higher frequency, and turn it to the
left to tune to a lower frequency.
play that station for about 10 seconds.
If you do nothing, the system will
then scan for the next strong station
and play it for 10 seconds. When it
plays a station you want to listen to,
press the SCAN side of the bar again.
SEEK/SKIP － The seek function
searches up and down from the
current frequency to find a station
with a strong signal. To activate it,
reproduction on AM is not available.
press the
or
side of the
SEEK bar, then release it.
146
09/07/16 18:09:38 31SWA630_152
Playing the AM/FM Radio (LX model)
Preset － Each preset button can
store one frequency on AM and two
frequencies on FM.
AUTO SELECT － If you are
If you do not like the stations auto
select has stored, you can store
other frequencies on the preset
buttons as previously described.
traveling and can no longer receive
your preset stations, you can use the
auto select feature to find stations in
the local area.
1. Select the desired band, AM or
FM. You can store one frequency
To turn off auto select, press the
A. SEL side of the bar. This restores
the presets you originally set.
on FM1, and one frequency on FM Press the left side of the
2 with each preset button.
A. SEL/SCAN bar. You will see
A. SEL flashing in the display, and
the system goes into scan mode for
several seconds. It stores the
frequencies of six AM, and twelve
FM stations in the preset buttons.
2. Use the tune, seek, or scan
function to tune the radio to a
desired station.
For information on AM/FM radio
frequencies and reception, see page
250.
3. Pick a preset button (1－6), and
hold it until you hear a beep.
You will see a ‘‘0’’ displayed after
pressing a preset button if auto
select cannot find a strong station for
every preset button.
4. Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
147
09/07/16 18:09:54 31SWA630_153
Playing the AM/FM Radio (LX model)
Adjusting the Sound
SVC － Adjusts the volume level
adjust the setting to your liking. If
you feel the sound is too loud,
choose low. If you feel the sound is
too quiet, choose high.
Press the SOUND (TUNE) knob
repeatedly to display the BASS,
TREBLE, FADER, BALANCE, and
SVC (speed-sensitive volume
compensation) settings.
based on the vehicle speed.
Each mode is shown in the display as
it changes. Turn the TUNE knob to
adjust the setting to your liking.
This function is set to MID as the
default setting when the vehicle
leaves the factory.
BASS － Adjusts the bass.
Except SVC adjustment
When the level reaches the center,
you will see ‘‘C’’ in the display.
TREBLE － Adjusts the treble.
Audio System Lighting
You can use the instrument panel
brightness control knob to adjust the
illumination of the audio system (see
page 79 ). The audio system
FADER － Adjusts the front-to-back
strength of the sound.
The system will return to the audio
display about 5 seconds after you
stop adjusting a mode.
BALANCE － Adjusts the side-to-
side strength of the sound.
illuminates when the parking lights
are on, even if the radio is turned off.
Speed-sensitive Volume
Compensation (SVC)
The SVC mode controls the volume
based on vehicle speed. The faster
you go, the louder the audio volume
becomes. As you slow down, the
audio volume decreases.
The SVC has four modes: SVC OFF,
SVC LOW, SVC MID, and SVC
HIGH. Turn the TUNE knob to
148
2024 Honda CR-V Owner's Manual
2023 Honda CR-V Owner's Manual
2021 Honda CR-V Owner's Manual
2018 Honda CR-V Owner's Manual
2015 Honda CR-V Owner's Manual
