Audio System*
About Your Audio System
Models with navigation system
1About Your Audio System
See the Navigation System Manual for operation on the navigation system.
Video CDs, DVDs, and 8-cm (3-inch) mini CDs are not
supported.
The audio system features AM/FM radio. It can also play audio CDs*, WMA/MP3/
AAC files, USB flash drives, and iPod, iPhone, and Bluetooth® devices.
iPod, iPhone and iTunes are trademarks of Apple Inc.
After you turn the ignition switch to LOCK (0*1, you
can use the audio system for up to 30 minutes per
driving cycle. However, whether you can continue
using the audio system depends on the battery
condition. Repeatedly using this feature may drain
the battery.
You can operate the audio system from the buttons and switches on the panel, or
the remote controls on the steering wheel or on the touch screen interface*.
Audio system with
two displays
Remote Control
Audio system with
one display
*1: Models withthe keyless access systemhave an ENGINE
START/STOP button instead of an ignition switch.
iPod
iPod
USB Flash
Drive
USB Flash
Drive
HDMITM
* Not available on all models
240
uuAudio System*uUSB Adapter Cable*
USB Adapter Cable*
1. Unclip the USB connector and loosen the
adapter cable.
2. Install the iPod dock connector or the USB
flash drive to the USB connector.
1USB Adapter Cable*
•
Do not leave the iPod or USB flash drive in the
vehicle. Direct sunlight and high temperatures may
damage it.
•
•
•
Do not use an extension cable with the USB
adapter cable.
Do not connect the iPod or USB flash drive using a
hub.
Do not use a device such as a card reader or hard
disk drive, as the device or your files may be
damaged.
•
•
We recommend keeping your data backed up
before using the device in your vehicle.
Displayed messages may vary depending on the
device model and software version.
If the audio system does not recognize the iPod, try
reconnecting it a few times or reboot the device. To
reboot, follow the manufacturer’s instructions
* Not available on all models
241
uuAudio System*uUSB Ports*
USB Ports*
1USB Ports*
1. Open the cover.
2. Install the iPod USB connector or the USB
flash drive to the USB port.
•
Do not leave the iPod or USB flash drive in the
vehicle. Direct sunlight and high temperatures may
damage it.
•
•
•
We recommend using an extension cable with the
USB port.
Do not connect the iPod or USB flash drive using a
hub.
Do not use a device such as a card reader or hard
disk drive, as the device or your files may be
damaged.
•
•
We recommend keeping your data backed up
before using the device in your vehicle.
Displayed messages may vary depending on the
device model and software version.
If the audio system does not recognize the iPod, try
reconnecting it a few times or reboot the device. To
reboot, follow the manufacturer’s instructions
* Not available on all models
242
uuAudio System*uAuxiliary Input Jack*
Auxiliary Input Jack*
1Auxiliary Input Jack*
Use the jack to connect standard audio devices.
1. Open the cover.
To switch the mode, press any of the audio mode
buttons. You can return to the AUX mode by
pressing the CD/AUX button.
2. Connect a standard audio device to the
input jack using a 3.5mm (1/8 inch) stereo
miniplug.
u The audio system automatically switches
to the AUX mode.
You cannot use the auxiliary input jack if you replace
the audio system.
HDMITM Port*
1HDMITM Port*
•
Do not leave the HDMITM connected device in the
vehicle. Direct sunlight and high temperatures may
damage it.
1. Open the cover.
2. Install the HDMITM cable to the HDMITM
port.
•
•
We recommend keeping your data backed up
before using the device in your vehicle.
Displayed messages may vary depending on the
device model and software version.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
* Not available on all models
243
uuAudio System*uAudio System Theft Protection
Audio System Theft Protection
The audio system is disabled when it is disconnected from the power source, such as
when the battery is disconnected or goes dead. In certain conditions, the system
may display a passcode input mode. If it does, reactivate the audio system.
■
Reactivating the audio system
1. Turn the ignition switch to ON (w*1
2. Turn on the audio system.
.
3. Press and hold the audio system power button for more than two seconds.
u The audio system is reactivated when the audio control unit establishes a
connection with the vehicle control unit. If the control unit fails to recognise
the audio unit, you must go to a dealer and have the audio unit checked.
*1: Models with the keyless access system have an ENGINE START/STOP button instead of an
ignition switch.
244
uuAudio System*uAudio Remote Controls
Audio Remote Controls
Allow you to operate the audio system while driving.
1Audio Remote Controls
SOURCE Button
Cycles through the audio modes as follows:
Some mode appears only when an appropriate
device or medium is used.
SOURCE Button
Audio system with one display
FM1FM2DAB1*DAB2*LWMW
CDAUX
(+ Button
Depending on the Bluetooth® device you connect,
some functions may not be operated.
Button
Button
Audio system with two displays
(- Button
FMLWMWDABCD*USBiPod
AppsBluetooth® AudioAUX HDMITM
MENU Button
(+ (- (Volume) Buttons
Press (+: To increase the volume.
Press (-: To decrease the volume.
Buttons
• When listening to the radio
Press : To select the next preset radio station.
Press : To select the previous preset radio station.
Press and hold : To select the next strong station.
To select the next service (DAB*).
Press and hold : To select the previous strong station.
To select the previous service (DAB*).
• When listening to a CD*, iPod, USB flash drive, or Bluetooth® Audio
Press : To skip to the next song.
Press : To go back to the beginning of the current or previous song.
• When listening to a CD* or USB flash drive
Press and hold : To skip to the next folder.
Press and hold : To go back to the previous folder.
* Not available on all models
Continued
245
uuAudio System*uAudio Remote Controls
Audio system with two displays
1Audio Remote Controls
Steering Wheel MENU Button
Audio system with two displays
• When listening to the radio
The MENU button is available only when the audio
mode is FM, AM, CD*, USB, iPod, or Bluetooth®
Audio.
Press and hold the MENU button: To select the radio station by Scan, Save
Preset, or Seek.
• When listening to a CD* or USB flash drive
Press and hold the MENU button: To select the song by Scan, Repeat,
Random, or Play/Pause*.
• When listening to an iPod
Press and hold the MENU button: To select the song by Repeat or Shuffle.
• When listening to a Bluetooth® Audio
Press and hold the MENU button: To select Pause or Play for the song.
* Not available on all models
246
Audio System Basic Operation
Audio system with one display
To use the audio system, the ignition switch must be in ACCESSORY (q or ON (w*1
1Audio System Basic Operation
.
These indications are used to show how to operate
the selector knob.
Use the selector knob or SETUP button to
access some audio functions.
SETUP Button
Rotate
Press
to select.
to enter.
Press
to switch between the normal and
Press the SOURCE, (+
steering wheel to change any audio setting.
,
(-
,
or
button on the
extended display for some functions.
Button
2 Audio Remote Controls P. 245
Setup menu items
Selector Knob
Menu Display
2 Sound settings P. 248
2 RDS settings P. 252
2 DAB settings P. 258
2 Play mode P. 261
2 Resume/Pause P. 269
Selector knob: Rotate left or right to scroll
through the available choices. Press
your selection.
to set
SETUP button: Press to select any mode such
as the Sound settings, Radio Data System
(RDS) settings, DAB settings, Play mode,
Resume/Pause, Radio text or Adjust clock.
button: Press to go back to the
Adjust clock
previous display.
*1: Models with the keyless access system have an ENGINE START/STOP button instead of an
ignition switch.
247
uuAudio System Basic OperationuAdjusting the Sound
Adjusting the Sound
1Adjusting the Sound
Press the SETUP button, and rotate
to
select Sound settings, then press . Rotate
to scroll through the following choices:
SETUP Button
The SVC has four modes: Off, Low, Mid, and High.
SVC adjusts the volume level based on the vehicle
speed. As you go faster, audio volume increases. As
you slow down, audio volume decreases.
Selector Knob
Bass
BAS
TRE
FAD
BAL
SVC
Treble
Fader
Balance
Adjust clock
Speed-sensitive
Volume
Compensation
Treble is selectable.
248
uuAudio System Basic OperationuPlaying AM/FM Radio
Playing AM/FM Radio
(Power) Button
Press to turn the audio
system on and off.
/
Button
Press to tune a station.
Preset Buttons (1-6)
To store a station:
AM Button
FM/DAB Button*/FM Button*
Press to select a band.
1. Tune to the selected station.
2. Pick a preset button and hold it
until you hear a beep.
To listen to a stored station, select a
band, then press the preset button.
SCAN Button
Press to sample each of the
strongest stations on the
selected band for 10 seconds.
To turn off scan, press the
button again.
TA Button
Press to activate the TA stand
by function.
Selector Knob
Turn to adjust the volume.
Press and turn to select a station
with the FM selected.
/
(Seek/Skip) Buttons
SETUP Button
AM: Press to search up and down the selected
band for a station with a strong signal.
Press to display menu items.
FM: Press to update the station list or skip to
the next station.
* Not available on all models
Continued
249
uuAudio System Basic OperationuPlaying AM/FM Radio
1Playing AM/FM Radio
Radio Data System (RDS)
Provides convenient automated services related to your selected RDS capable FM
station.
■
The ST indicator appears on the display indicating
stereo FM broadcasts.
Stereo reproduction in AM is not available.
Switching the Audio Mode
Press the SOURCE button on the steering wheel.
2 Audio Remote Controls P. 245
You can store 12 AM stations and 12 FM stations into
the preset button memory. AM has two types of
frequencies LW and MW, and each lets you store six
stations. FM1 and FM2 let you store six stations each.
1Radio Data System (RDS)
When you select an RDS capable FM station, the RDS
automatically turns on, and the frequency display
changes to the station name. However, when the
signals of that station become weak, the display
changes from the station name to the frequency.
250
uuAudio System Basic OperationuPlaying AM/FM Radio
■
To find an RDS station from Station List
1Radio Data System (RDS)
1. Press
2. Rotate
.
while listening to a FM station.
to select the station, then press
While listening to a FM station on Station list,
pressing
station.
/
(Seek/Skip) button changes the
If the system find a station on Station list, a
confirmation message for updating the list appears.
Rotate
to select Yes, then press to
update
the list.
■
Manual Update
Updates your available station list at any time.
1. Press
while listening to a FM station.
2. Rotate
to select Update list, then press
.
■
Available RDS functions
Alternative Frequency (AF):
Automatically changes the frequency of the same programme as you enter different
regions.
Regional Programme (REG):
Keeps the same frequency of the stations within that region even if the signal gets
weak.
News Programme (NEWS):
Automatically tunes to the news programme.
Continued
251
uuAudio System Basic OperationuPlaying AM/FM Radio
■
Setting the RDS functions
1Radio Data System (RDS)
1. Press the SETUP button with the FM
selected.
Turning the Alternative Frequency (AF) function on
and off turns the RDS on and off.
2. Rotate
to select RDS settings and press
Adjust clock
Pressing
off.
switches the function between on and
.
3. Each RDS function is displayed every time
you rotate
4. Press to select a function.
.
252
uuAudio System Basic OperationuPlaying AM/FM Radio
1Radio Data System (RDS)
■
TA (Traffic announcement) button
TA standby function allows the system to stand by for traffic announcements in any
mode. The last tuned station must be an RDS capable traffic programme station.
TA
When you press the TA button, the TA indicator
appears on the display.
To turn the function on: Press the TA button. When a traffic announcement
begins on your last tuned station, the system automatically switches to the FM
mode. TA-Information appears on the display. The system returns to your last
selected mode after the traffic announcement is finished.
If you press the SCAN button while the TA standby
function is on, the system searches TP station only.
Pressing the TA button while the traffic
announcement is on does not cancel the TA standby
function.
If you want to go back to your last selected mode during the traffic announcement,
press the TA button again.
To cancel the function: Press the TA button.
Continued
253
uuAudio System Basic OperationuPlaying AM/FM Radio
■
PTY (Programme type)/News interrupt function
Allows the system to interrupt with a newscast in any mode. The last tuned station
must be the NEWS PTY coded station.
To activate the function: Select NEWS from RDS settings and display the NEWS
PTY before changing to other modes. When a newscast begins on your last tuned
station, the system automatically switches to the FM mode.
2 Setting the RDS functions P. 252
The system returns to your last selected mode if changed to another programme, or
signal gets weak.
■
PTY alarm
The PTY code, ALARM is used for emergency announcements, such as natural
disasters. When this code is received, ALARM appears on the display and the system
interrupts your audio operation.
254
uuAudio System Basic OperationuPlaying DAB (Digital Audio Broadcasting)*
Playing DAB (Digital Audio Broadcasting)*
The DAB indicator appears on the
display when the DAB band is
selected.
/
Button
●
●
Press to tune a DAB ensemble.
Press and hold to search up and down
top station in the DAB ensemble with
a strong signal. The top station within
this ensemble is selected.
(Power) Button
Press to turn the audio
system on and off.
SCAN Button
Preset Buttons (1-6)
Press to sample each of the
strongest stations on the
station list for 10 seconds.
To turn off scan, press the
button again.
To store a station:
1. Tune to the selected station.
2. Pick a preset button and hold it
until you hear a beep.
To listen to a stored station, select a
band, then press the preset button.
FM/DAB Button
Press to select a band.
Selector Knob
Turn to adjust the volume.
Press and turn to select a station
on the station list or ensemble.
/
(Seek/Skip) Buttons
SETUP Button
Press to skip the station on the station
list.
Press to display menu items.
* Not available on all models
Continued
255
uuAudio System Basic OperationuPlaying DAB (Digital Audio Broadcasting)*
1To find an DAB station from Service List or Ensemble List
To find an DAB station from Service List or Ensemble List
■
If the system cannot find a station, a confirmation
message for updating the list appears. Rotate
1. Press
2. Rotate
.
while selecting the DAB mode.
to select the station, then press
to
select Yes, then press
to update the list.
u If you select Update list, the system
update the station list.
256
uuAudio System Basic OperationuPlaying DAB (Digital Audio Broadcasting)*
■
Setting the DAB functions
1. Press the SETUP button with the DAB
selected.
2. Rotate
press
to select DAB settings and
.
3. Each DAB function is displayed every time
you rotate
.
4. Press
to select a function.
5. Rotate
to select a setting, then press
.
Continued
257
uuAudio System Basic OperationuPlaying DAB (Digital Audio Broadcasting)*
DAB Settings
■
■
DAB-Link:
Automatically searches for the same station from Ensembles, and switches to it.
■
FM-Link:
If the system finds the same station from a FM band, it automatically switches the
band.
■
Band select:
You can select specific bands. This can reduces the time to update the lists, and
search for a station.
1Radio Text
Radio Text
■
The TEXT indicator appears on the display indicating
radio text information.
1. Press the SETUP button with the DAB
selected.
2. Rotate
to select Radio text and press
.
258
uuAudio System Basic OperationuPlaying a CD
Playing a CD
Your audio system supports audio CDs, CD-Rs and CD-RWs in either MP3 or WMA
format. With the CD loaded, press the CD/AUX button.
SCAN Button
You will get a 10-second
sampling of each song.
Press to sample all tracks
(Power) Button
Press to turn the audio
system on and off.
●
Track AAA
on the CD (all files in the
current folder in MP3 or
WMA).
Press twice to sample the
first file in each of the main
folders (MP3 or WMA).
To turn off scan, press and
hold the button.
1’23’’
Genre AAA
Artist AAA
●
●
CD Slot
Insert a CD about halfway into the
CD slot.
CD/AUX Button
Press to play a CD.
(CD Eject) Button
Press to eject a CD.
/
Button
to skip to the
Press
next folder, and
to skip to
the beginning of the previous
folder in MP3 or WMA.
Selector Knob
Turn to adjust the volume.
Press and turn to select an item,
then press to set your selection.
/
(Seek/Skip) Buttons
SETUP Button
Press
or
to change tracks
Press to display menu items.
(files in MP3 or WMA).
Continued
259
uuAudio System Basic OperationuPlaying a CD
1Playing a CD
How to Select a File from a Folder with the Selector Knob
(MP3/WMA)
■
NOTICE
Do not use CDs with adhesive labels. The label can
cause the CD to jam in the unit.
1. Press
list.
to switch the display to a folder
WMA files protected by digital rights management
(DRM) cannot be played.
The audio system displays Unsupported, then skips
to the next file.
Track AAA
1’23’’
Genre AAA
Artist AAA
Text data appears on the display under the following
circumstances:
•
•
•
When you select a new folder, file, or track.
When you change the audio mode to CD.
When you insert a CD.
Folder Selection
2. Rotate
to select a folder.
Folder BBB
Folder CCC
Folder AAA
If you eject the CD but do not remove it from the slot,
the system reloads the CD automatically after several
seconds.
Track Selection
3. Press
to change the display to a list of
files in that folder.
Track BBB
Track CCC
Track AAA
4. Rotate to select a file, then press
.
260
uuAudio System Basic OperationuPlaying a CD
1How to Select a Play Mode
How to Select a Play Mode
■
Play mode menu items
Normal play
Repeat one track: Repeats the current track/file(s).
Repeat one folder (MP3/WMA): Repeats all files in
the current folder.
You can select repeat and random modes when playing a track or file.
1. Press the SETUP button.
Sound settings
RDS settings
Random in folder (MP3/WMA): Plays all files in the
current folder in random order.
Random all: Plays all tracks/files in random order.
Play Mode
Items
2. Rotate
.
3. Rotate
to select Play mode, then press
to select a mode, then press
.
■
To turn off a play mode
1. Press the SETUP button.
2. Rotate
3. Rotate
to select Play mode, then press
to select Normal play, then press
.
.
261
uuAudio System Basic OperationuPlaying an iPod
Playing an iPod
Connect the iPod using your dock connector to the USB adapter cable, then press
the CD/AUX button.
2 USB Adapter Cable* P. 241
USB Indicator
Appears when an iPod is connected.
Album Art
(Power) Button
/
Button
Press to turn the audio
system on and off.
Press
previous display.
to go back to the
Press to set your selection.
CD/AUX Button
Press to select iPod (if connected).
Selector Knob
Turn to adjust the volume.
Press and turn to select an item,
then press to set your selection.
/
(Seek/Skip) Buttons
SETUP Button
Press to display menu items.
Press
songs.
or
to change
* Not available on all models
262
uuAudio System Basic OperationuPlaying an iPod
1Playing an iPod
How to Select a File from the iPod Menu
■
Available operating functions vary on models or
versions. Some functions may not be available on the
vehicle’s audio system.
1. Press
to display the iPod menu.
If there is a problem, you may see an error message
on the i-multi-information display.
2 iPod/USB Flash Drive P. 316
iPod Menu
2. Rotate
to select a menu.
3. Press
to display the items on that menu.
4. Rotate
to select an item, then press
.
All
Artist AAA
Artist BBB
Continued
263
uuAudio System Basic OperationuPlaying an iPod
1How to Select a Play Mode
How to Select a Play Mode
■
Play mode menu items
Normal play
You can select repeat and shuffle modes when playing a track.
1. Press the SETUP button.
Shuffle off: Turns off the shuffle mode.
Shuffle: Plays all available tracks in a selected list
(playlists, artists, albums, songs, genres, or
composers) in random order.
Shuffle albums: Plays all available albums in a
selected list (playlists, artists, albums, songs, genres,
or composers) in random order.
Sound settings
RDS settings
Repeat off: Turns off the repeat mode.
Repeat one track: Repeats the current track.
Play Mode
Items
2. Rotate
.
to select Play mode, then press
to select a mode, then press
Normal play
3. Rotate
.
Shuffle off
Shuffle
■
To turn off a play mode
1. Press the SETUP button.
2. Rotate
3. Rotate
to select Play mode, then press
to select Normal play, then press
.
.
264
uuAudio System Basic OperationuPlaying a USB Flash Drive
Playing a USB Flash Drive
Your audio system reads and plays sound files on a USB flash drive in either MP3,
WMA or AAC*1 format.
Connect your USB flash drive to the USB adapter cable, then press the CD/AUX
button.
2 USB Adapter Cable* P. 241
123 456
File AAA
USB Indicator
Appears when a USB flash drive
is connected.
1’23’’
Genre AAA
Artist AAA
/
Button
Press
next folder, and
to skip to the
to skip to
the beginning of the previous
folder.
(Power) Button
Press to turn the audio
system on and off.
SCAN Button
You will get a 10-second
sampling of each file.
CD/AUX Button
Press to select USB flash drive
(if connected).
●
Press to sample all files in
the current folder.
Press twice to sample the
●
Selector Knob
Turn to adjust the volume.
Press and turn to select an item, then
press to set your selection.
first file in each of the main
folders.
To turn off scan, press and
●
hold the button.
SETUP Button
Press to display menu items.
/
(Seek/Skip) Buttons
Press
or
to change files.
*1:Only AAC format files recorded with iTunes are playable on this unit.
* Not available on all models
Continued
265
uuAudio System Basic OperationuPlaying a USB Flash Drive
1Playing a USB Flash Drive
How to Select a File from a Folder with the Selector Knob
■
Use the recommended USB flash drives.
2 General Information on the Audio System
P. 319
1. Press
to switch the display to a folder
list.
123 456
File AAA
Files in WMA format protected by digital rights
management (DRM) are not played.
The audio system displays Unplayable file, and then
skips to the next file.
1’23’’
Genre AAA
Artist AAA
If there is a problem, you may see an error message
on the i-multi-information display.
2 iPod/USB Flash Drive P. 316
Folder Selection
2. Rotate
to select a folder.
121:Folder BBB
122:Folder CCC
123:Folder AAA
Track Selection
3. Press
to change the display to a list of
files in that folder.
454:File BBB
4. Rotate to select a file, then press
.
455:File CCC
456:File AAA
266
uuAudio System Basic OperationuPlaying a USB Flash Drive
1How to Select a Play Mode
How to Select a Play Mode
■
Play mode menu items
Normal play
Repeat one track: Repeats the current file.
Repeat one folder: Repeats all files in the current
folder.
You can select repeat and random when playing a file(s).
1. Press the SETUP button.
Sound settings
Random in folder: Plays all files in the current folder
in random order.
Random all: Plays all files in random order.
RDS settings
Play Mode
Items
2. Rotate
.
to select Play mode, then press
to select a mode, then press
3. Rotate
.
■
To turn off a play mode
1. Press the SETUP button.
2. Rotate
3. Rotate
to select Play mode, then press
to select Normal play, then press
.
.
267
uuAudio System Basic OperationuPlaying Bluetooth® Audio
Playing Bluetooth® Audio
Your audio system allows you to listen to music from your Bluetooth-compatible
1Playing Bluetooth® Audio
phone.
Not all Bluetooth-enabled phones with streaming
audio capabilities are compatible with the system.
You can find an approved phone by visiting:
This function is available when the phone is paired and connected to the vehicle’s
Hands-Free Telephone (HFT) system.
2 Phone Setup P. 346
•
Europe:
In some countries, it may be illegal to perform some
data device functions while driving.
123456
Bluetooth Indicator
Appears when your
phone is connected
to HFT.
File AAA
If more than one phone is paired to the system, there
will be a delay before the system begins to play.
Genre AAA
Artist AAA
Some functions may not be available on some
devices.
Selector Knob
Turn to adjust the
volume.
Press to display the
device’s name.
(Power) Button
Press to turn the
audio system on
and off.
Preset 1 Button
CD/AUX Button
Press to switch the
mode between
pause and resume.
Press to select
Bluetooth® Audio.
/
(Seek/Skip) Buttons
SETUP Button
Press
or
to change files.
Press to display
menu items.
268
uuAudio System Basic OperationuPlaying Bluetooth® Audio
1To Play Bluetooth® Audio Files
To Play Bluetooth® Audio Files
■
To play the audio files, you may need to operate your
phone. If so, follow the phone maker’s operating
instructions.
1. Make sure that your phone is paired and
connected to the system.
2. Press the CD/AUX button.
Sound settings
The pause function may not be available on some
phones.
If the phone is not recognized, another HFT-
compatible phone, which is not compatible
for Bluetooth® Audio, may already be
connected.
If any audio device is connected to the auxiliary input
jack, you may need to press the CD/AUX button
repeatedly to select the Bluetooth® Audio system.
Switching to another mode pauses the music playing
from your phone.
■
To pause or resume a file
1. Press the SETUP button.
2. Rotate
to select Resume/Pause, then press
.
Each time you press , the setting switches between pause and resume.
269
Audio System Basic Operation
Audio system with two displays
1Audio System Basic Operation
To use the audio system function, the ignition switch must be in ACCESSORY (q or
Audio Menu Items
2 Station List P. 291
2 How to Select a File from the Music Search
List (MP3/WMA/AAC) P. 297, 303
2 Scan P. 294
ON (w*1
(Menu) Button
(Home) Button
.
(Home) Button: Press to go to the home
screen.
2 Switching the Display P. 272
2 How to Select a Play Mode P. 298, 301, 304
(Menu) Button: Press to select any mode.
The available mode includes Change Source,
Station List, Save Preset, Radio Text,
Music Search, and play modes. Play modes
can be also selected from Scan, Random/
Repeat, and so on.
When the battery has been reconnected or replaced,
the next start-up may take a few minutes for the
audio system to start. Wait a few moments while the
system is starting up.
Press and hold the
(Power) button for
(Day/Night) Button
(Back) Button
(Back) Button: Press to go back to the
previous display when it is displayed.
approximately 10 seconds to reset the system.
When the system is reset and started up, you are
required to input the password.
(Day/Night) button:
Press to change the audio/information screen
brightness.
2 Audio System Theft Protection P. 244
Press the
button once and select (- or
(+ to make an adjustment.
u Each time you press the
button, the
mode switches among the daytime
mode, nighttime mode and off mode.
*1: Models with the keyless access system have an ENGINE START/STOP button instead of an
ignition switch.
270
uuAudio System Basic Operationu
Models with navigation system
1How to access the disc slot
■
How to access the disc slot
If you eject the CD but do not remove it from the slot,
the system reloads the CD automatically after several
seconds.
Press the (Eject/CLOSE) button to open the
screen.
u The screen folds back, and the CD slot
Do not use the folded down screen as a tray.
appears.
Models without keyless access system
You cannot open the screen when the key is in the
ignition switch.
Press the
the screen to the upright position.
(Eject/CLOSE) button to return
Models with keyless access system
You cannot open the screen when the power mode
is in VEHICLE OFF.
(Eject/CLOSE) Button
CD Slot
(Eject/CLOSE) Button
271
2024 Honda CR-V Owner's Manual
2023 Honda CR-V Owner's Manual
2021 Honda CR-V Owner's Manual
2018 Honda CR-V Owner's Manual
2015 Honda CR-V Owner's Manual
