Does the HDS indicate PASSED, FAILED, or NOT COMPLETED?
PASSED Troubleshooting is complete. Check for other DTC after this troubleshooting. If any other Pending or
Confirmed DTCs were indicated, go to the indicated DTC's troubleshooting.
FAILED Troubleshooting is incomplete. Go to step 3 and recheck.
NOT COMPLETED Repair verification is incomplete. Meet the test condition, and check the OBD STATUS
again.
DTC P1733: SHIFT ERROR E
Fig. 127: DTC Troubleshooting Flow Chart (P1733)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot with
the HDS, and review the General Troubleshooting Information See HOW TO
TROUBLESHOOT THE A/T SYSTEM or HOW TO TROUBLESHOOT THE FUEL
AND EMISSIONS SYSTEMS .
DTC Description
Confirmed DTC
Pending DTC
Freeze Frame
P1733 Shift Error E
1. ATF check:
ο‘
ο‘
ο‘
1. Warm up the engine to normal operating temperature (the radiator fan comes on).
2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
3. DRAIN THE ATF through a strainer. Inspect the strainer for metal debris or excessive clutch
material.
Does the strainer have metal debris or excessive clutch material?
YES : Replace the transmission See AUTOMATIC TRANSMISSION DISASSEMBLY AND
REASSEMBLY or AUTOMATIC TRANSMISSION REMOVAL AND INSTALLATION , then do
the repair verification .
NO : REPLACE THE ATF , then go to step 2.
2. Problem verification:
ο‘
ο‘
ο‘
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five
gears.
ο‘
4. Monitor the OBD STATUS for P1733 in the DTCs MENU with the HDS.
DTC Description OBD Status
P1733 Shift Error E
Does the HDS indicate FAILED?
YES : The failure is duplicated. Go to step 3.
NO : If the HDS indicates PASSED, intermittent failure, the system is OK at this time. If the HDS
indicates NOT COMPLETED, test-drive again.
3. Shift solenoid valve D operation check:
ο‘
1. Clear the DTC with the HDS.
ο‘
2. Select Shift Solenoid Valve D in the Miscellaneous Test Menu, and check that shift solenoid
valve D operates with the HDS.
Is a clicking sound heard?
YES : Shift solenoid valve D is OK. Go to step 4.
NO : REPLACE SHIFT SOLENOID VALVE D , then do the repair verification .
4. A/T clutch pressure control solenoid valve C operation check:
ο‘
1. Select Clutch Pressure Control (Linear) Solenoid Valve C in the Miscellaneous Test Menu, and
test A/T clutch pressure control solenoid valve C with the HDS.
Does the HDS indicate NORMAL?
NORMAL A/T clutch pressure control solenoid valve C is OK. Intermittent failure, the system is OK at
this time.
FAILURE (HDS has not determined cause) Follow the instructions indicated on the HDS according to
the test result. If the HDS has not determined the cause of the failure, go to step 5.
FAILURE (HDS has determined cause) Follow the instructions indicated on the HDS according to the
test result. If a part is replaced, do the repair verification .
5. A/T clutch pressure control solenoid valve C check:
ο‘
1. Inspect A/T clutch pressure control solenoid valve C See A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE A TEST or A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE B AND C TEST .
Does A/T clutch pressure control solenoid valve C work properly?
YES : A/T clutch pressure control solenoid valve C is OK. Repair the hydraulic system related with shift
valve D, or replace the transmission See AUTOMATIC TRANSMISSION DISASSEMBLY AND
REASSEMBLY or AUTOMATIC TRANSMISSION REMOVAL AND INSTALLATION , then do
the repair verification .
NO : Replace A/T clutch pressure control solenoid valve C See A/T CLUTCH PRESSURE
CONTROL SOLENOID VALVE A REMOVAL AND INSTALLATION or A/T CLUTCH
PRESSURE CONTROL SOLENOID VALVE B AND C REMOVAL AND INSTALLATION , then
do the repair verification .
REPAIR VERIFICATION (OBD STATUS CHECK)
ο‘
ο‘
ο‘
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Test-drive the vehicle with the shift lever in D, and let the transmission shift through all five gears.
ο‘
4. Monitor the OBD STATUS for P1733 in the DTCs MENU with the HDS.
DTC Description OBD Status
P1733 Shift Error E
Does the HDS indicate PASSED, FAILED, or NOT COMPLETED?
PASSED Troubleshooting is complete. Check for other DTC after this troubleshooting. If any other Pending or
Confirmed DTCs were indicated, go to the indicated DTC's troubleshooting.
FAILED Troubleshooting is incomplete. Go to step 3 and recheck.
NOT COMPLETED Repair verification is incomplete. Meet the test condition, and check the OBD STATUS
again.
DTC P1734: SHIFT ERROR F
2024 Honda CR-V Owner's Manual
2023 Honda CR-V Owner's Manual
2021 Honda CR-V Owner's Manual
2018 Honda CR-V Owner's Manual
2015 Honda CR-V Owner's Manual
