Download
Table of Contents > A/T CONTROL SYSTEM (DIAGNOSTIC CODES) > DTC P0971: A/T Clutch Pressure Control Solenoid Valve C

Honda CR-V A/T CONTROL SYSTEM (DIAGNOSTIC CODES) ➜ DTC P0971: A/T Clutch Pressure Control Solenoid Valve C

ο‚‘
ο‚‘
4. Start the engine, and wait for at least 1 second.  
5. Monitor the OBD STATUS for P0970 in the DTCs MENU with the HDS.  
DTC Description  
OBD Status  
P0970 A/T Clutch Pressure Control Solenoid Valve C (Open or Short)  
Does the HDS indicate PASSED, FAILED, or NOT COMPLETED?  
PASSED Troubleshooting is complete. If the PCM was substituted, replace the original PCM See PCM  
REMOVAL AND INSTALLATION or PCM UPDATE . Check for other DTC after this troubleshooting. If  
any other Pending or Confirmed DTCs were indicated, go to the indicated DTC's troubleshooting.  
FAILED Troubleshooting is incomplete. Check for poor connections or loose terminals between A/T clutch  
pressure control solenoid valve C and the PCM, then go to step 1 and recheck. If the PCM was updated,  
substitute a known-good PCM See PCM REMOVAL AND INSTALLATION or PCM UPDATE , and  
check the OBD STATUS again.  
NOT COMPLETED Repair verification is incomplete. Meet the test condition, and check the OBD STATUS  
again.  
DTC P0971: A/T CLUTCH PRESSURE CONTROL SOLENOID VALVE C  
Fig. 83: DTC Troubleshooting Flow Chart (P0971)  
Courtesy of AMERICAN HONDA MOTOR CO., INC.  
NOTE:  

Before you troubleshoot, record all freeze data and any on-board snapshot  
with the HDS, and review the General Troubleshooting Information See  
HOW TO TROUBLESHOOT THE A/T SYSTEM or HOW TO  
TROUBLESHOOT THE FUEL AND EMISSIONS SYSTEMS .  

This code is caused by an electrical circuit problem and cannot be caused  
by a mechanical problem in the transmission.  
DTC Description  
Confirmed DTC Pending DTC Freeze Frame  
P0971 A/T Clutch Pressure Control Solenoid Valve C  
1. Problem verification (DTC check):  
ο‚‘
ο‚‘
ο‚‘
ο‚‘
1. Turn the ignition switch to ON (II).  
2. Clear the DTC with the HDS.  
3. Start the engine, and wait for at least 1 second.  
4. Check for Pending or Confirmed DTCs with the HDS.  
Confirmed  
DTC  
Pending  
DTC  
Freeze  
Frame  
DTC Description  
P0971 A/T Clutch Pressure Control Solenoid  
Valve C  
Is DTC P0971 indicated?  
YES : The failure is duplicated. Go to step 4.  
NO : Go to step 2.  
2. A/T clutch pressure control solenoid valve C operation check:  
ο‚‘
1. Select Clutch Pressure Control (Linear) Solenoid Valve C in the Miscellaneous Test Menu, and  
test A/T clutch pressure control solenoid valve C with the HDS.  
Does the HDS indicate NORMAL?  
YES : The A/T clutch pressure control solenoid valve C operation is OK. Go to step 3.  
NO : Go to step 4.  
3. Problem verification (OBD STATUS check):  
ο‚‘
1. In the Clutch Pressure Control Solenoid Valve Control MENU, set A/T clutch pressure control  
solenoid valve C at 0.2 A with the HDS.  
ο‚‘
2. Monitor the OBD STATUS for P0971 in the DTCs MENU with the HDS.  
DTC Description  
OBD Status  
P0971 A/T Clutch Pressure Control Solenoid Valve C  
Does the HDS indicate FAILED?  
YES : The failure is duplicated. Go to step 4.  
NO : If the HDS indicates PASSED, intermittent failure, the system is OK at this time. Check for poor  
connections or loose terminals between A/T clutch pressure control solenoid valve C and the PCM. If the  
HDS indicates NOT COMPLETED, do the function test again.  
4. A/T clutch pressure control solenoid valve C internal resistance check:  
ο‚‘
1. Turn the ignition switch to LOCK (0).  
2. Disconnect the following connector.  
ο‚‘
A/T clutch pressure control solenoid valve C 2P connector  
3. Measure the resistance between test points 1 and 2.  
Test condition IG LOCK (0)  
ο‚‘
A/T clutch pressure control solenoid valve C 2P connector: disconnected  
Test circuit LINEAR C+, PG2  
Test point 1 A/T clutch pressure control solenoid valve C 2P connector No. 1  
Test point 2 A/T clutch pressure control solenoid valve C 2P connector No. 2  
Fig. 84: Measuring Resistance Between A/T Clutch Pressure Control Solenoid Valve C 2P  
Connector No. 1 And No. 2  
Courtesy of AMERICAN HONDA MOTOR CO., INC.  
Is there 4.9-6.4 ohms?  
YES : A/T clutch pressure control solenoid valve C is OK. Go to step 5.  
NO : REPLACE A/T CLUTCH PRESSURE CONTROL SOLENOID VALVE C , then do the  
repair verification .  
5. Open wire check (PG2 line):  
ο‚‘
1. Check for continuity between test points 1 and 2.  
Test condition IG LOCK (0)  
A/T clutch pressure control solenoid valve C 2P connector: disconnected  
Test circuit PG2  
Test point 1 A/T clutch pressure control solenoid valve C 2P connector No. 1 (BLK)  
Test point 2 Body ground  
Fig. 85: Checking Continuity Between A/T Clutch Pressure Control Solenoid Valve C 2P  
Connector No. 1 (BLK) And Body Ground  
Courtesy of AMERICAN HONDA MOTOR CO., INC.  
Is there continuity?  
YES : The PG2 wire is OK. Update the PCM if it does not have the latest software See PCM  
REMOVAL AND INSTALLATION or PCM UPDATE , or substitute a known-good PCM See  
PCM REMOVAL AND INSTALLATION or PCM UPDATE , then do the repair verification .  
NO : Repair an open in the PG2 wire between A/T clutch pressure control solenoid valve C and ground  
(G101) or repair poor ground (G101), then do the repair verification .  
REPAIR VERIFICATION (OBD STATUS CHECK)  
ο‚‘
ο‚‘
1. Reconnect all connectors.  
2. Turn the ignition switch to ON (II).  
ο‚‘
ο‚‘
ο‚‘
3. Clear the DTC with the HDS.  
4. Start the engine, and wait for at least 1 second.  
5. Monitor the OBD STATUS for P0971 in the DTCs MENU with the HDS.  
DTC Description  
OBD Status  
P0971 A/T Clutch Pressure Control Solenoid Valve C  
Does the HDS indicate PASSED, FAILED, or NOT COMPLETED?  
PASSED Troubleshooting is complete. If the PCM was substituted, replace the original PCM See PCM  
REMOVAL AND INSTALLATION or PCM UPDATE . Check for other DTC after this troubleshooting. If  
any other Pending or Confirmed DTCs were indicated, go to the indicated DTC's troubleshooting.  
FAILED Troubleshooting is incomplete. Check for poor connections or loose terminals between A/T clutch  
pressure control solenoid valve C and the PCM, then go to step 1 and recheck. If the PCM was updated,  
substitute a known-good PCM See PCM REMOVAL AND INSTALLATION or PCM UPDATE , and  
check the OBD STATUS again.  
NOT COMPLETED Repair verification is incomplete. Meet the test condition, and check the OBD STATUS  
again.  
DTC P0973: SHIFT SOLENOID VALVE A (SHORT)