YES : Leave the engine off for at least 6 hours, then go to step 3.
NO : REPLACE THE ATF TEMPERATURE SENSOR .
3. ATF temperature sensor check:
ο‘
1. Compare the values of the ATF Temperature Sensor and ECT SENSOR 2.
A/T SYSTEM
Current conditions
Signal
Values
Unit
ATF Temperature
PGM-FI SYSTEM
Current conditions
Values Unit
Signal
ECT SENSOR 2
Is the value of the ATF Temperature Sensor higher than the value of ECT SENSOR 2 by 58 Β°F (32 Β°C), or
is the value of the ATF Temperature Sensor lower than the value of ECT SENSOR 2 by 43 Β°F (24 Β°C)?
YES : REPLACE THE ATF TEMPERATURE SENSOR .
NO : The ATF temperature sensor is OK. Intermittent failure, the system is OK at this time.
DTC P0716: INPUT SHAFT (MAINSHAFT) SPEED SENSOR
(RANGE/PERFORMANCE)
Fig. 12: DTC Troubleshooting Flow Chart (P0716)
Courtesy of AMERICAN HONDA MOTOR CO., INC.
NOTE:
ο¬
Before you troubleshoot, record all freeze data and any on-board snapshot
with the HDS, and review the General Troubleshooting Information See
HOW TO TROUBLESHOOT THE A/T SYSTEM or HOW TO
TROUBLESHOOT THE FUEL AND EMISSIONS SYSTEMS .
ο¬
This code is caused by an electrical circuit problem and cannot be caused
by a mechanical problem in the transmission.
Confirmed
DTC
Pending
DTC
Freeze
Frame
DTC Description
P0716 Input Shaft (Mainshaft) Speed Sensor
(Range/Performance)
1. DTC check:
ο‘
ο‘
ο‘
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Raise the vehicle on a lift. Make sure it is securely supported, and allow the front wheels to
rotate freely.
ο‘
ο‘
4. Start the engine, disable the VSA by pressing the VSA OFF button, run the vehicle with the shift
lever in D, and keep the vehicle speed at speeds over 12 mph (20 km/h) for at least 10 seconds.
Slow down, and stop the wheels.
5. Check for Pending or Confirmed DTCs with the HDS.
Confirmed
DTC
Pending
DTC
Freeze
Frame
DTC Description
P0718 Input Shaft (Mainshaft) Speed Sensor
(Intermittent Failure)
Is DTC P0718 indicated?
YES : DO THE TROUBLESHOOTING FOR DTC P0718.
NO : Go to step 2.
2. Problem verification:
ο‘
1. Check for Pending or Confirmed DTCs with the HDS.
Confirmed
DTC
Pending
DTC
Freeze
Frame
DTC Description
P0716 Input Shaft (Mainshaft) Speed Sensor
(Range/Performance)
Is DTC P0716 indicated?
YES : The failure is duplicated. Go to step 3.
NO : Intermittent failure, the system is OK at this time.
3. Input shaft (mainshaft) speed sensor connection check:
Are the connection and installation OK?
YES : The connection and installation are OK. REPLACE THE INPUT SHAFT (MAINSHAFT)
SPEED SENSOR , then do the repair verification .
NO : Repair faulty connection or installation, then do the repair verification .
REPAIR VERIFICATION
ο‘
ο‘
ο‘
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, disable the VSA by pressing the VSA OFF button, run the vehicle with the shift lever
in D, and keep the vehicle speed at speeds over 12 mph (20 km/h) for at least 10 seconds. Slow down, and
stop the wheels.
ο‘
4. Check for Pending or Confirmed DTCs with the HDS.
Confirmed
DTC
Pending
DTC
Freeze
Frame
DTC Description
P0716 Input Shaft (Mainshaft) Speed Sensor
(Range/Performance)
Is DTC P0716 indicated?
YES : Troubleshooting is incomplete. Go to step 1.
NO : Troubleshooting is complete.
DTC P0717: INPUT SHAFT (MAINSHAFT) SPEED SENSOR (NO SIGNAL
INPUT)
2024 Honda CR-V Owner's Manual
2023 Honda CR-V Owner's Manual
2021 Honda CR-V Owner's Manual
2018 Honda CR-V Owner's Manual
2015 Honda CR-V Owner's Manual
