uuGauges and Driver Information InterfaceuDriver Information Interface
Driver Information Interface
The driver information interface shows information such as the estimated travelable
distance and fuel economy of the vehicle. It also displays messages such as warnings
and other helpful information.
When a warning message displays, please check the message and contact a dealer
to have the vehicle inspected if necessary. Please refer to the pages below if the
Engine oil pressure low, Engine temperature too hot or Limited stopping
power! message is displayed.
2 If the Engine oil pressure low Warning Appears P. 676
2 Overheating P. 674
2 If the Limited stopping power Warning Appears P. 677
Switching the Display
■
You can add or delete the meter contents.
2 Gauge Display Settings P. 134
Press the
(home) button, then roll the left selector wheel to scroll to the content
you want to see. Press the left selector wheel to see detailed information.
Continued
117
uuGauges and Driver Information InterfaceuDriver Information Interface
Warnings
Power flow
Speed & time
P. 134
P. 119
P. 123
Range & fuel
P. 121
Audio
P. 124
Gauge display
settings
P. 134
Settings*
Phone
P. 124
P. 135
Navigation*
Brightness
P. 133
P. 125
Left Selector
Wheel
(Home) Button
Seat belts
P. 130
Driver
attention
P. 126
No content
P. 132
Roll the left
selector wheel.
Safety
support
Maintenance
P. 130
AWD torque
distribution*
P. 130
P. 129
* Not available on all models
118
uuGauges and Driver Information InterfaceuDriver Information Interface
Power Flow/Engine Status Display/High Voltage Battery
■
Charge Level Gauge
The High Voltage battery charge level may decrease
under the following conditions:
• When the 12-volt battery has been replaced.
• When the 12-volt battery has been disconnected.
• When the High Voltage battery control system
corrects its reading.
Displays the power flow of the motor and engine, indicating the vehicle’s power
source, remaining battery level, and whether the battery is being charged.
2WD models
High Voltage
Battery Charge
Level Gauge
Engine ON
Engine OFF
Power Flow
Engine
The charge level reading will be corrected
automatically while driving.
Changes in the temperature of the High Voltage
battery can increase or decrease the battery’s charging
capacity. If temperature changes cause the battery’s
capacity to change, the number of indicators in the
battery charge level gauge may also change, even if
the amount of charge remains the same.
Hybrid (HV)
Electric Vehicle (EV)
Engine (Direct Drive)
While the vehicle is stationary with the engine
running, the following may appear on the driver
information interface.
Power is supplied
by the motor and
the engine.
Power is supplied
by the motor.
The engine is running
and the motor is
charging the High
Voltage battery.
2WD models
Regeneration
Power is being
supplied by the
engine only.
The engine is running
and the motor is
charging the High
Voltage battery.
The motor is
charging the High
Voltage battery.
Continued
119
uuGauges and Driver Information InterfaceuDriver Information Interface
AWD models
1Power Flow/Engine Status Display/High Voltage Battery Charge
Level Gauge
Engine ON
AWD models
High Voltage
Battery Charge
Level Gauge
Power Flow
Engine
Engine OFF
Hybrid (HV)
Electric Vehicle (EV)
Engine (Direct Drive)
Power is supplied
by the motor and
the engine.
Power is supplied
by the motor.
The engine is running
and the motor is
charging the High
Voltage battery.
Regeneration
Power is being
supplied by the
engine only.
The engine is running
and the motor is
charging the High
Voltage battery.
The motor is
charging the High
Voltage battery.
120
uuGauges and Driver Information InterfaceuDriver Information Interface
Range / Fuel / Trip Meter
■
Roll the left selector wheel to switch between trip meter A and trip meter B.
Average Fuel Economy
Range
Trip Meter A
Trip Meter B
Instant Fuel Economy
Continued
121
uuGauges and Driver Information InterfaceuDriver Information Interface
■ Trip meter
Shows the total number of miles or kilometers driven since the last reset. Meters A
and B can be used to measure two separate trips.
Resetting a trip meter
To reset the trip meter, display it, press the left selector wheel and then select Reset.
u The trip meter is reset to 0.0.
■ Average Fuel Economy
Shows the estimated average fuel economy of each trip meter in mpg or l/100 km.
The display is updated at set intervals. When a trip meter is reset, the average fuel
economy is also reset.
You can change when to reset the average fuel
economy.
2 Settings* P. 135
2 Customized Features P. 376
■ Instant Fuel Economy
Shows the instant fuel economy as a bar graph in mpg or l/100 km.
■ Range
Shows the estimated distance you can travel on the remaining power and fuel. This
estimated distance is based on the vehicle’s current fuel economy.
The driving range displayed is only an estimate and
may differ to the actual distance the vehicle can
travel.
* Not available on all models
122
uuGauges and Driver Information InterfaceuDriver Information Interface
Speed / Time / Trip Meter
■
Roll the left selector wheel to switch between trip meter A and trip meter B.
Elapsed Time
Average Speed
Trip Meter A
Trip Meter B
Continued
123
uuGauges and Driver Information InterfaceuDriver Information Interface
■ Trip meter
2 Trip meter P. 122
■ Elapsed time
Shows the time elapsed since Trip A or Trip B was reset.
You can change when to reset the elapsed time.
2 Settings* P. 135
2 Customized Features P. 376
■ Average speed
Shows the average speed in mph or km/h since Trip A or Trip B was reset.
You can change when to reset the average speed.
2 Settings* P. 135
2 Customized Features P. 376
Audio
■
Shows the current audio information.
2 Audio System Basic Operation P. 246, 271
Phone
■
Shows the current phone information.
2 Bluetooth® HandsFreeLink® P. 400, 420
* Not available on all models
124
uuGauges and Driver Information InterfaceuDriver Information Interface
Navigation*
■
You can select whether to have the turn-by-turn
display come on or not during the route guidance.
2 Customized Features P. 376
■ Compass
Shows the compass screen.
Turn-by-turn directions may not be available for all
apps.
■ Turn-by-Turn Directions
When driving guidance is provided by the navigation system*, Android Auto or
Apple CarPlay, turn-by-turn directions to your destination appear.
2 Refer to the Navigation System Manual
Models with navigation system
When the compass or turn-by-turn directions are
displayed, you can control some navigation system
functions on the driver information interface by
scrolling the left selector wheel.
2 Android AutoTM P. 336
2 Apple CarPlay P. 329
2 Refer to the Navigation System Manual
* Not available on all models
Continued
125
uuGauges and Driver Information InterfaceuDriver Information Interface
Driver Attention Monitor
■
The Driver Attention Monitor cannot always detect if
the driver is tired or inattentive.
Regardless of the system’s feedback, if you are
feeling tired, stop in a safe location and rest for as
long as needed.
The Driver Attention Monitor analyzes steering inputs to determine if the vehicle is
being driven in a manner consistent with drowsy or inattentive driving. If it
determines that the vehicle is being driven in such a manner, it will display the
degree of the driver’s attention on the driver information interface.
Driver Information
Interface
Left Selector
Wheel
(Home) Button
When you select Driver attention on the
driver information interface, bars on it light up
in white to indicate the degree of the driver’s
attention.
2 Switching the Display P. 117
Level
126
uuGauges and Driver Information InterfaceuDriver Information Interface
If two bars light up, the Driver attention
level low message will appear.
If one bar lights up, the Driver attention
level low. Time for a break. message will
appear, a beep will sound, and the steering
wheel will vibrate.
If this message appears, stop in a safe location
and rest for as long as needed.
The message will disappear when the left
selector wheel is pressed or when the system
has determined that the driver is driving
normally.
If the driver does not take a break and the
monitor continues to detect that the driver is
very tired, the message will appear again after
approximately 15 minutes, accompanied by a
beep and steering wheel vibrations.
The message does not appear when the
traveling time is 30 minutes or less.
Continued
127
uuGauges and Driver Information InterfaceuDriver Information Interface
■ The Driver Attention Monitor resets when:
• The power system is turned off.
• The driver unfastens the seat belt and opens the door while the vehicle is stopped.
■ For the Driver Attention Monitor to function:
• The vehicle must be traveling above 25 mph (40 km/h).
• The electric power steering (EPS) system indicator must be off.
The bars on the driver information interface remain
grayed out unless the Driver Attention Monitor is
functioning.
■ Depending on driving conditions or other factors, the Driver Attention
Monitor may not function in the following circumstances:
• The steering assist function of the Lane Keeping Assist System (LKAS) is active.
2 Lane Keeping Assist System (LKAS) P. 533
• The condition of the road is poor; e.g., the surface is unpaved or bumpy.
• It is windy.
• The driver is frequently operating the vehicle in an assertive manner, such as
changing lanes or accelerating.
■ Customizing
You can change the Driver Attention Monitor settings. Select Tactile and audible
alert*1/Tactile And Audible Alert*2, Tactile alert*1/Tactile Alert*2, or OFF.
2 Settings* P. 135
2 Customized Features P. 376
*1: Models with 7-in. Color Touchscreen
*2: Models with 9-in. Color Touchscreen
* Not available on all models
128
uuGauges and Driver Information InterfaceuDriver Information Interface
AWD Torque Distribution Monitor*
■
The indicators on the display show the
amount of torque being transferred to the
right front, left front, right rear, and left rear
wheels.
2 Real Time AWD with Intelligent Control
SystemTM* P. 479
* Not available on all models
Continued
129
uuGauges and Driver Information InterfaceuDriver Information Interface
Seat Belts
■
Occurs, under specified conditions, when seat belts are latched or unlatched.
2 Seat Belt Reminder P. 51
Maintenance
Shows the remaining oil life and Maintenance MinderTM.
2 Maintenance MinderTM P. 603
■
Safety Support
■
If a system is indicated by the color amber, have your
vehicle checked by a dealer immediately.
Indicates the status of the Road Departure Mitigation system, CMBSTM, Low Speed
Braking Control*, Blind Spot Information System, and Parking Sensor System*, such
as On, Off, or Failure, by color and letters.
To turn on or off each system, first rotate the left
selector wheel to switch displays. From the next
display you can select which system to turn on or off.
2 Road Departure Mitigation System P. 554
2 Collision Mitigation Braking SystemTM
(CMBSTM) P. 495
2 Blind Spot Information System P. 487
2 Low Speed Braking Control* P. 507
2 Parking Sensor System* P. 584
The following colors indicate the status of any of the above-mentioned systems:
• Green: The system is on.
• Gray: The system is off.
• Amber: There is a problem with the system.
You can also confirm the status of each function by
the color of the safety support indicator.
2 Safety Support Indicator (Amber) P. 111
2 Safety Support Indicator (Green/Gray)
P. 113
* Not available on all models
130
uuGauges and Driver Information InterfaceuDriver Information Interface
1Safety Support
Area Info
Models with Low Speed Braking Control
for CMBSTM
Even when the Low Speed Braking Control icon is
green, if the Rear Sensor Setting is turned off, the
brake assist will not operate when reversing.
2 Customized Features P. 376
Area Info
for Road
Departure
Mitigation
System
Road
Departure
Mitigation
System Icon
and Status
Info
CMBSTM
Models with Parking Sensor System
Icon and
Even when the Parking Sensor System icon is green,
Status
Info
if the Rear Sensor Setting is turned off, the rear
parking sensor will not operate when reversing.
2 Customized Features P. 376
Models with Low Speed
Braking Control
Blind Spot
Information
System Icon
and Status
Info
Low
Speed
Braking
Control
Icon and
Status
Info
Area Info
for Blind
Spot
Information
System
Area Info for Low
Speed Braking
Control
Models with Parking
Sensor System
Area Info
for Parking
Sensor
Parking
Sensor
System
System
Icon and
Status Info
Continued
131
uuGauges and Driver Information InterfaceuDriver Information Interface
No Content
2 POWER Gauge P. 114
■
2 CHARGE/DECEL Gauge P. 114
■ Speed/Distance Units
Enables you to show another unit on the driver information interface and audio/
information screen and set the displayed measurements to read in either miles and
mph or km and km/h.
Press and hold the left selector wheel when you select No content on the driver
information interface. Each time you do this, the unit will change from miles and
mph to km and km/h or vice versa. After this, a confirmation screen will appear for
a few seconds.
132
uuGauges and Driver Information InterfaceuDriver Information Interface
Brightness
■
The brightness of the gauge is automatically adjusted
depending on the ambient brightness.
Display the adjustment for instrument panel brightness.
• The brightness dims when the ambient light is
dark.
• The brightness brightens when the ambient light is
bright.
When the power mode is in ON, you can use the left selector wheel to adjust
instrument panel brightness.
Brighten: Roll the left selector wheel up.
Dim: Roll the left selector wheel down.
You can change the setting even when the ambient
lighting is bright, but the brightness of the gauge
won’t change.
Press the left selector wheel to exit.
Continued
133
uuGauges and Driver Information InterfaceuDriver Information Interface
Gauge Display Settings
■
Icons that are gray cannot be removed from the
home screen.
You can choose which icons to display on the home screen.
1. Roll the left selector wheel to scroll to select
Gauge display settings, then press the
left selector wheel.
When you customize settings, shift to (P.
2. Roll the left selector wheel.
3. Roll the left selector wheel to scroll
between icons, then press the left selector
wheel to check or uncheck them.
Warnings
■
If there are multiple warnings, you can roll the left
selector wheel to see other warnings.
You can check if there are any active warning messages.
134
uuGauges and Driver Information InterfaceuDriver Information Interface
Settings*
■
To customize other features, roll the left selector
wheel.
Use the driver information interface to customize certain features.
2 List of customizable options P. 136
2 Example of customization settings P. 142
■ How to customize
Press the
(home) button, then select the
screen by rolling the left selector
When you customize settings, shift to (P.
wheel while the power mode is in ON, the vehicle is at a complete stop, and the shift
position is in (P. Then, press the left selector wheel.
Driver
Information
Interface
(Home) Button
Left Selector Wheel
* Not available on all models
Continued
135
uuGauges and Driver Information InterfaceuDriver Information Interface
■ List of customizable options
Setup Group
Customizable Features
Description
Selectable Settings
TPMS
—
Calibrates the TPMS.
Cancel/Calibrate
calibration*
Forward collision
warning distance
Changes the distance at which CMBSTM alerts.
Long/Normal*1/Short
ON/OFF*1
Causes the system to beep when a vehicle is detected or
when the vehicle is out of ACC with Low Speed Follow
range.
ACC forward vehicle
detect beep
Driver assist
system setup
Road departure
mitigation setting
Changes the setting for the Road Departure Mitigation
system.
Narrow/Normal*1/Wide/
Warning only
Lane keeping assist
suspend beep
Causes the system to beep when the LKAS is suspended. ON/OFF*1
Audible and visual
Blind spot information Changes the setting for the blind spot information.
alert*1/Visual alert
*1:Default Setting
* Not available on all models
136
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
ON*1/OFF
Traffic sign
recognition system
display setting
Turns the traffic sign recognition system on and off.
Traffic sign
recognition system
exceeding speed
warning
Turns the traffic sign recognition system over speed
warning on and off.
ON/OFF*1
Speed limit*1/
Speed limit+3mph/
Speed limit+5mph/
Speed limit+10mph
(When mph is selected)
Speed limit*1/
Driver assist
system setup
Speed limit warning
threshold setting
Changes at which speed the traffic sign recognition
system over speed warning is activated.
Speed limit+5km/h/
Speed limit+10km/h/
Speed limit+15km/h
(When km/h is selected)
Driver attention
monitor
Tactile and audible
Changes the setting for the driver attention monitor.
alert*1/ Tactile alert/OFF
*1:Default Setting
Continued
137
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
English*1/Français/
Español
Language selection
Changes the displayed language.
-5°F ~ 0°F*1 ~ +5°F
(U.S.)
-3°C ~ 0°C*1 ~ +3°C
(Canada)
Adjust outside temp.
display
Adjusts the temperature reading by a few degrees.
Changes the setting of how to reset trip meter A,
average fuel economy A, average speed A, and elapsed
time A.
When fully refueled/
“Trip A” reset timing
IGN OFF/Manually reset*1
Changes the setting of how to reset trip meter B,
average fuel economy B, average speed B, and elapsed
time B.
When fully refueled/
Meter setup
“Trip B” reset timing
Adjust alarm volume
IGN OFF/Manually reset*1
Changes the alarm volume, such as buzzers, warnings,
turn signal sound, and so on.
High/Mid*1/Low
Fuel efficiency backlight Turns the ambient meter feature on and off.
ON*1/OFF
ON*1/OFF
Rear seat reminder
Turns the Rear Seat Reminder feature on and off.
km/h∙km/mph∙miles*1
(U.S.)
km/h∙km*1/mph∙miles
(Canada)
Speed/distance units
Selects the trip meter units.
*1:Default Setting
138
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
Changes which doors unlock when you grab the driver’s Driver door only*1/All
Door unlock mode
door handle.
doors
Keyless access light
flash
Causes some exterior lights to flash when you unlock/
lock the doors.
ON*1/OFF
Keyless access
setup
Causes the beeper to sound when you unlock/lock the
doors.
Keyless access beep
ON*1/OFF
Remote start system
ON/OFF
Turns the remote engine start feature on and off.
Turns the auto high-beam on and off.
ON*1/OFF
Auto high-beam
ON*1/OFF
Interior light dimming
time
Changes the length of time the interior lights stay on
after you close the doors.
60sec/30sec*1/15sec
Headlight auto off
Lighting setup timer
Changes the length of time the exterior lights stay on
after you close the driver’s door.
60sec/30sec/15sec*1/0sec
Max/High/Mid*1/Low/Min
Auto light sensitivity*
Changes the timing for the headlights to come on.
Changes the settings for the wiper operation when the
headlights automatically come on while the headlight
switch is in the AUTO position.
Auto headlight ON
with wiper ON
ON*1/OFF
*1:Default Setting
* Not available on all models
Continued
139
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
Changes the setting for when the doors and the tailgate With vehicle speed*1/
Auto door lock
automatically lock.
Shift from P/OFF
All doors when driver’s
door opens*1/All doors
when shifted to Park/
All doors when ignition
switched OFF/OFF
Changes the setting for when the doors and the tailgate
automatically unlock.
Auto door unlock
Changes the settings for the automatic locking the
doors when you walk away from the vehicle while
carrying the keyless remote.
Walk away auto lock
ON/OFF*1
Door setup
Keyless lock answer
back
LOCK/UNLOCK - The exterior lights flash.
LOCK (2nd push) - The beeper sounds.
ON*1/OFF
ON*1/OFF
Keyless remote power
window control
Turns remote window control using the keyless remote
on and off.
Changes the settings for the lockout protection
function.
Lockout prevention
Lock presetting
ON*1/OFF
ON*1/OFF
Changes the settings for the Lock Presetting function.
*1:Default Setting
140
uuGauges and Driver Information InterfaceuDriver Information Interface
Setup Group
Customizable Features
Description
Selectable Settings
Changes the keyless setting for when the power tailgate Anytime*1/When
Keyless open mode
opens.
Unlocked
Power tailgate
setup*
Power open by outer
handle
Changes the setting to open power tailgate by tailgate
outer handle.
OFF (Manual only)/ON
(Power/Manual)*1
Maintenance
reset
Resets the Maintenance MinderTM display when you
have performed the maintenance service.
—
—
(Selects Reset Items)
Cancels customized changes you have made or restores
them to their default setting.
Default all
Cancel/Set
*1:Default Setting
* Not available on all models
Continued
141
uuGauges and Driver Information InterfaceuDriver Information Interface
■ Example of customization settings
The steps for changing the “Trip A” reset timing setting to When fully refueled
are shown below. The default setting for “Trip A” reset timing is Manually reset.
1. Press the
selector wheel to select
press the left selector wheel.
(home) button and roll the left
screen, then
142
uuGauges and Driver Information InterfaceuDriver Information Interface
2. Roll the left selector wheel until Meter
setup appears on the display.
3. Press the left selector wheel.
4. Roll the left selector wheel until “Trip A”
reset timing appears on the display, then
press the left selector wheel.
u The display switches to the
customization setup screen, where you
can select When fully refueled, IGN
OFF, Manually reset, or Back.
5. Roll the left selector wheel and select
When fully refueled, then press the left
selector wheel.
u The display will return to the
customization menu screen.
Continued
143
uuGauges and Driver Information InterfaceuDriver Information Interface
6. Press the left selector wheel after Back
appears on the display.
7. Repeat Step 6 until you return to the
normal screen.
144
Controls
This chapter explains how to operate the various controls necessary for driving.
Canadian models
Clock ..................................................146
Locking and Unlocking the Doors
Key..................................................148
Low Keyless Remote Signal Strength ...150
Locking/Unlocking the Doors from the
Outside..........................................151
Locking/Unlocking the Doors from the
Inside.............................................161
Childproof Door Locks .....................163
Auto Door Locking/Unlocking ..........164
Tailgate.............................................. 165
Security System
Windows ............................................... 179
Moonroof.......................................... 183
Operating the Switches Around the
Steering Wheel
POWER Button................................. 184
Turn Signals..................................... 187
Light Switches.................................. 188
Daytime Running Lights ................... 192
Auto High-Beam.............................. 193
Wipers and Washers ........................ 196
Rear Defogger/Heated Door Mirror Button ... 199
Heated Windshield Button............... 199
Driving Position Memory System* .... 200
Adjusting the Steering Wheel .......... 202
Mirrors............................................... 203
Seats.................................................. 205
Interior Convenience Items.............. 216
Climate Control System
Using Automatic Climate Control .... 232
Automatic Climate Control Sensors ......236
Immobilizer System .......................... 176
Security System Alarm......................176
* Not available on all models
145
2024 Honda CR-V Owner's Manual
2023 Honda CR-V Owner's Manual
2021 Honda CR-V Owner's Manual
2018 Honda CR-V Owner's Manual
2015 Honda CR-V Owner's Manual
