Fig. 42: Installing Door Mirror Cover
Courtesy of AMERICAN HONDA MOTOR CO., INC.
DOOR LOCK KNOB SWITCH TEST
REMOVAL
1. Door Mirror Cover
1. Carefully pry out the door mirror cover (A) with the appropriate trim tool to detach the clips (B),
then remove the door mirror cover.
2. With tweeter: Disconnect the connector (C).
Fig. 43: Removing Door Mirror Cover
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Front Door Power Window Switch Panel
1. Carefully pry out on the notch (A) in the power window switch panel (B) with the appropriate trim
tool to detach the clips (C) and the hooks (D). Disconnect the connectors (E), then remove the
power window switch panel.
Fig. 44: Removing Power Window Switch Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Front Door Panel
1. Carefully pry out on the upper hook (A) in the inner handle cap (B) with the appropriate trim tool,
then pull back the inner handle cap to remove it.
Fig. 45: Removing Inner Handle Cap
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Remove the screws (A) securing the inner handle (B).
Fig. 46: Identifying Inner Handle And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Remove the pull pocket mat (A), then remove the screw (B).
Fig. 47: Identifying Pull Pocket Mat And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Starting at the bottom edge of the door panel (A), detach the clips (B) with a commercially
available trim pad remover.
5. Starting at the rear, pull the door panel upward.
6. Remove the inner handle (C) from the door panel, then remove the door panel.
Fig. 48: Removing Door Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Rear Door Power Window Switch Panel
1. Carefully pry out on the notch (A) in the power window switch panel (B) with the appropriate trim
tool to detach the clips (C) and the hooks (D). Disconnect the connector (E), then remove the power
window switch panel.
Fig. 49: Removing Power Window Switch Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Rear Door Panel
1. Detach the clip (A) and the hooks (B), then remove the rear door quarter inner trim (C).
Fig. 50: Removing Rear Door Quarter Inner Trim
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Carefully pry out on the upper hook (A) in the inner handle cap (B) with the appropriate trim tool,
then pull back the inner handle cap to remove it.
Fig. 51: Removing Inner Handle Cap
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Remove the screws (A) securing the inner handle (B).
Fig. 52: Identifying Inner Handle And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Remove the pull pocket mat (A), then remove the screw (B).
Fig. 53: Identifying Pull Pocket Mat And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Starting at the bottom edge of the door panel (A), detach the clips (B) with a commercially
available trim pad remover.
6. Starting at the rear, pull the door panel up.
7. Remove the inner handle (C) from the door panel, then remove the door panel.
Fig. 54: Removing Door Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
TEST
1. Front Door Lock Knob Switch - Test
1. Disconnect the connector.
2. Check for continuity between the terminals in each switch position according to the table.
3. If the continuity is not as specified, the front door lock knob switch is faulty; replace the front door
latch (A).
4. Connect the connector.
Fig. 55: Identifying Driver Door Latch Connector Terminals
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Driver's door
Fig. 56: Driver Door Latch Switch Continuity Reference Chart
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Passenger's door
Fig. 57: Passenger Door Latch Switch Continuity Reference Chart
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Rear Door Lock Knob Switch - Test
1. Disconnect the connector.
2. Check the actuator operation by connecting power and ground according to the table.
3. If the continuity is not as specified, the door lock knob switch is faulty; replace the rear door latch
(A).
4. Connect the connector.
Fig. 58: Identifying Rear Door Latch Connector Terminals
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 59: Rear Door Latch Switch Continuity Reference Chart
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION
1. Rear Door Panel
1. Install the inner handle (A) in the door panel (B).
2. Install the door panel. Make sure the clips (C) snap into place securely.
Fig. 60: Installing Rear Door Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Install the screw (A), then install the pull pocket mat (B).
Fig. 61: Identifying Pull Pocket Mat And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Install the screws (A) securing the inner handle (B).
Fig. 62: Identifying Inner Handle And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Install the inner handle cap (A). Make sure the upper hook (B) and the lower hooks (C) snap into
place securely.
Fig. 63: Installing Inner Handle Cap
Courtesy of AMERICAN HONDA MOTOR CO., INC.
6. Install the rear door quarter inner trim (A). Make sure the clip (B) and the hooks (C) snap into place
securely.
Fig. 64: Installing Rear Door Quarter Inner Trim
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Rear Door Power Window Switch Panel
1. Connect the connector (A), then install the power window switch panel (B). Make sure the clips (C)
and the hooks (D) snap into place securely.
Fig. 65: Installing Rear Door Power Window Switch Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Front Door Panel
1. Install the inner handle (A) in the door panel (B).
2. Install the door panel. Make sure the clips (C) snap into place securely.
Fig. 66: Installing Front Door Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Install the screw (A), then install the pull pocket mat (B).
Fig. 67: Identifying Pull Pocket Mat And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Install the screws (A) securing the inner handle (B).
Fig. 68: Identifying Inner Handle And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Install the inner handle cap (A). Make sure the upper hook (B) and the lower hooks (C) snap into
place securely.
Fig. 69: Installing Inner Handle Cap
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Front Door Power Window Switch Panel
1. Connect the connectors (A), then install the power window switch panel (B). Make sure the clips
(C) and the hooks (D) snap into place securely.
Fig. 70: Installing Front Door Power Window Switch Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Door Mirror Cover
1. With tweeter: Connect the connector (A).
2. Install the door mirror cover (B). Make sure the clips (C) snap into place securely.
Fig. 71: Installing Door Mirror Cover
Courtesy of AMERICAN HONDA MOTOR CO., INC.
KEYLESS ENTRY TRANSMITTER TEST
TEST
1. HDS DLC - Connection
1. Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the
dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle. If it does not communicate, go to the DLC
circuit troubleshooting.
Fig. 72: Identifying Data Link Connector
2024 Honda CR-V Owner's Manual
2023 Honda CR-V Owner's Manual
2021 Honda CR-V Owner's Manual
2018 Honda CR-V Owner's Manual
2015 Honda CR-V Owner's Manual
