ο¬
Transmitter test
ο¬
ο¬
Poor ground (G402, G501, G604)
Blown No. B15 (10 A) and/or No. B30 (10
A) fuse in the under-dash fuse/relay box
Driver's door will not lock or unlock.
ο¬
ο¬
Door switch test (check the door switch
ON/OFF information with the HDS)
ACTUATOR TEST
ο¬
ο¬
Poor ground (G402, G501, G601, G604)
Blown No. B9 (10 A) and/or No. B33 (15 A)
fuse in the under-dash fuse/relay box
Left rear door will not lock or unlock.
ο¬
ο¬
MICU INPUT TEST
Door switch test (check the door switch
ON/OFF information with the HDS)
ο¬
ACTUATOR TEST
ο¬
ο¬
Poor ground (G402, G501, G503, G604)
Blown No. B8 (15 A) and/or No. B32 (15 A)
fuse in the under-dash fuse/relay box
Front passenger's and right rear doors will
not lock or unlock.
ο¬
ο¬
MICU INPUT TEST
Door switch test (check the door switch
ON/OFF information with the HDS)
ο¬
ACTUATOR TEST
Keyless operation does not work (LOCK,
UNLOCK, PANIC).
Keyless operation does not work (LOCK,
UNLOCK, PANIC)
Passenger doors will not unlock with the
Driver's door lock knob switch test (check for door
transmitter or key cylinder switch, but will lock knob switch ON/OFF information with the
unlock with the inside door unlock switch. HDS)
ο¬
Doors automatically relock 30 seconds
after being unlocked with the transmitter
even though a door has been opened
Doors automatically relock 30 seconds after
being unlocked with the transmitter even
though a door has been opened.
ο¬
Door switch test (check the door switch
ON/OFF information with the HDS)
The horn does not sound and/or the
headlights do not flash when the PANIC
button on the transmitter is pressed.
The horn does not sound and/or the headlights
do not flash when the PANIC button on the
transmitter is pressed
Security alarm system will not arm.
Auto door unlock does not work.
Security alarm system will not arm
Auto door unlock does not work
DOOR KEY CYLINDER SWITCH TEST
REMOVAL
1. Door Mirror Cover
1. Carefully pry out the door mirror cover (A) with the appropriate trim tool to detach the clips (B),
then remove the door mirror cover.
2. With tweeter: Disconnect the connector (C).
Fig. 1: Removing Door Mirror Cover
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Front Door Power Window Switch Panel
1. Carefully pry out on the notch (A) in the power window switch panel (B) with the appropriate trim
tool to detach the clips (C) and the hooks (D). Disconnect the connectors (E), then remove the
power window switch panel.
Fig. 2: Removing Power Window Switch Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Front Door Panel
1. Carefully pry out on the upper hook (A) in the inner handle cap (B) with the appropriate trim tool,
then pull back the inner handle cap to remove it.
Fig. 3: Removing Power Window Switch Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Remove the screws (A) securing the inner handle (B).
Fig. 4: Identifying Inner Handle And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Remove the pull pocket mat (A), then remove the screw (B).
Fig. 5: Identifying Pull Pocket Mat And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Starting at the bottom edge of the door panel (A), detach the clips (B) with a commercially
available trim pad remover.
5. Starting at the rear, pull the door panel upward.
6. Remove the inner handle (C) from the door panel, then remove the door panel.
Fig. 6: Removing Door Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
TEST
1. Door Key Cylinder Switch - Test
1. Disconnect the connector.
2. Check for continuity between the terminals in each switch position according to the table.
3. If the continuity is not as specified, the door key cylinder switch is faulty; replace the driver's door
latch (A).
4. Connect the connector.
Fig. 7: Identifying Driver Door Latch Connector Terminals
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig. 8: Driver Door Latch Switch Continuity Reference Chart
Courtesy of AMERICAN HONDA MOTOR CO., INC.
INSTALLATION
1. Front Door Panel
1. Install the inner handle (A) in the door panel (B).
2. Install the door panel. Make sure the clips (C) snap into place securely.
Fig. 9: Installing Front Door Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Install the screw (A), then install the pull pocket mat (B).
Fig. 10: Identifying Pull Pocket Mat And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Install the screws (A) securing the inner handle (B).
Fig. 11: Identifying Inner Handle And Screws
Courtesy of AMERICAN HONDA MOTOR CO., INC.
5. Install the inner handle cap (A). Make sure the upper hook (B) and the lower hooks (C) snap into
place securely.
Fig. 12: Installing Inner Handle Cap
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Front Door Power Window Switch Panel
1. Connect the connectors (A), then install the power window switch panel (B). Make sure the clips
(C) and the hooks (D) snap into place securely.
Fig. 13: Installing Front Door Power Window Switch Panel
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Door Mirror Cover
1. With tweeter: Connect the connector (A).
2. Install the door mirror cover (B). Make sure the clips (C) snap into place securely.
Fig. 14: Installing Door Mirror Cover
Courtesy of AMERICAN HONDA MOTOR CO., INC.
DOOR LOCK ACTUATOR TEST
REMOVAL
1. Door Mirror Cover
1. Carefully pry out the door mirror cover (A) with the appropriate trim tool to detach the clips (B),
then remove the door mirror cover.
2. With tweeter: Disconnect the connector (C).
Fig. 15: Removing Door Mirror Cover
Courtesy of AMERICAN HONDA MOTOR CO., INC.
2. Front Door Power Window Switch Panel
1. Carefully pry out on the notch (A) in the power window switch panel (B) with the appropriate trim
tool to detach the clips (C) and the hooks (D). Disconnect the connectors (E), then remove the
power window switch panel.
2024 Honda CR-V Owner's Manual
2023 Honda CR-V Owner's Manual
2021 Honda CR-V Owner's Manual
2018 Honda CR-V Owner's Manual
2015 Honda CR-V Owner's Manual
